Analisis Kekuatan Hasil Las Backing Ceramic Pada Proses Pengelasan Fcaw Material Baja Karbon A36
DOI:
https://doi.org/10.58192/ocean.v2i2.1150Keywords:
FCAW, Backing Ceramic, Uji Kekuatan TarikAbstract
Welding is an important thing in shipbuilding. There are several types of joints and types of materials with different material thicknesses, on of which is Flux Cored Arc Welding (FCAW). FCAW is a welding process that has a high level of productivity so that it is suitable for fabrication activities. Double-sided welding is often performed on joints. This causes time inefficiencies and costs quite a lot. Therefore, the solution so that welding is only done on one side, by using a backing ceramic. The Backing Ceramic is used to hold the welding penetration better and get better welding result. The purpose of this study was to determine the result of the strength of Backing Ceramic Weld on FCAW welding of A36 carbon steel material so that it can get perfect results, not defective and can be accepted according to the desired criteria.
References
Anzharie, D. C. A., Ari, M., & Kurniyanto, H. B. (2020). Analisis Penambahan Gas Argon Pada Gas Pelindung Flux Cored Arc Welding Terhadap Strukturmikro, Kekuatan Tarik Dan Nilai Kekerasan Pada Material A 516 Grade 70. In Prosiding Seminar Nasional NCIET (Vol. 1, Pp. 77-83).
ARIFIN, S. (2018). Analisa Pengaruh Variasi Kuat Arus Proses Pengelasan GMAW Terhadap Deformasi. Jurnal Teknik ITS, Surabaya
ASTM (American Society For Testing And Materials). 2010.Standard Test Methodsfor Flexural Properties Of Unreinforced And Reinforced Plastics And Electrical Insulating Materials, D – 790 Amerika : ASTM Interation
Biro Klasifikasi Indonesia (BKI).2022 Vol. VI Sec. 11 Mechanical And Technological Tests.
Biro Klasifikasi Indonesia (BKI).2022 Vol. VI Sec. 12 Welding Of Hull Structures.
Biro Klasifikasi Indonesia (BKI).2022 Vol. II Sec. 6 Shell Plating
BS EN ISO 5173.(2010) Destructive Tests On Welds In Metallic Materials — Bend Tests : British Standard
BS EN ISO 5817.(2014). Welding Fusion – Welded Joints In Steel, Titanium And Their Alloys(Beam Welding Excluded) – Quality Levels For Imperfections : British Standard.
Çevik, B. (2018). Analysis Of Welding Groove Configurations On Strength Of S275 Structural Steel Welded By FCAW. Journal Of Polytechnic.
Fahfudin, D. (2012). Analisa Jenis Sambungan Baja Karbon A36 Dengan Pengelasan FCAW. Jurnal Teknik ITS, Surabaya
Fauzi, M. H. (2018). Analisa Pengaruh Root Gap Pada Pengelasan. Jurnalteknik ITS,Surabaya.
IACS (International Association Of Classification Societies).Requirement Concerning Strength Of Ships.
Jeffus, L. (2011). Welding. Cengage Learning.
Nizar, H. 2014. Analisa Sifat Mekanik Dan Struktur Mikro Hasil Las Bawah Air Dengan Variasi Jenis Elektroda Pada Material ASTM 36. Tugas Akhir. Surabaya: Institut Teknologi Sepuluh Nopember
Okomura, T. Dan Harsono W. 1996. Teknologi Pengelasan Logam. Jakarta: PT Pradnya Paramita.
Hadi, Eko Sasmiko. 2009. Jurnal: Analisis Pengelasan Mild Steel (ST. 42) Dengan Proses SMAW, FCAW Dan SAW Ditinjau Dari Segi Kekuatan Dan Nilai Ekonomis. Teknik Perkapalan: Universitas Diponegoro.
Okumura, T. (1996). Teknologi Pengelasan Logam (1 Ed.). (H. Wiryosumarto, Trans.) Jakarta: Pradnya Paramita. Wiryosumarto, H. (1985). Teknologi Pengelasan Logam. Jakarta: Erlangga.
