Analisis Teknis Dan Ekonomis Perbandingan Efektivitas Proses Marking Rambu Bending Lambung Kapal Secara Manual Dan Semi Automatis
DOI:
https://doi.org/10.58192/ocean.v2i2.1126Keywords:
CNC Cutting, , Shipbuilding Project Effectiveness, Bending SignAbstract
This study aims to analyze the effectiveness and the economic side of the process of manual or semi-automatic bending signs. The data required for both types of marking methods are data on the number of operators, company working hours, effective working hours, and the results of the production process. After that it is done by data processing, data processing in this study uses the Experimental Method, in the Manual marking process, the process is done by directly drawing on the multiplex material according to the drawing design using 2 operators, in the Semi Automatic marking process, the use of a CNC machine is done by using only 1 operator and also using a setting on a CNC machine of 50 Amperes. So from the data that has been managed later, it shows that the use of CNC machines as a substitute for manual marking has a positive effect on the company. Which can reduce the amount of operator usage, get more results from the Manual marking process, and use less electricity. So overall, the marking process using the Semi Automatic method is better from all sides compared to the marking process using the Manual method.
References
Afandi, M. R., dan Basuki, M., ( 2022 ), Analisa Tekis dan Ekonomis Perbedaan Kuat Arus Pada Proses Pemotongan Plat Menggunakan CNC Plasma Cutting, Jurnal Semitan, 1(1), 214-220.
Endro, D. W., ( 2013 ), Hull Inspection Productivity Measurement For A New Shipbuilding Project, Vol.10, No. 2.
Hamid, A., Novareza, O., dan Dwi, T. W., ( 2018 ), Optimasi Proses Parameter Pemotongan Plasma Arc Cutting Pada Logam Aluminium Menggunakan Metode Taguchi.
Hardiana., Prasetyawati, D., dan Syahrir, I., ( 2019 ) Analisa Manajemen Proyek pada Proses Pembangunan Kapal Keruk di Galangan X, Jurnal Midship, Vol. 2, No. 1, 37-41.
Junisman, M. A., dan Mulyanto, T., ( 2020 ), Analisis Pengukuran Total Efektifitas Mesin Flame Cutting dan Plasma Cutting pada Perusahaan Industri Strategis, Jurnal Ilmiah Teknik Industri, Vol. 8, No. 3, 172-184.
Krajcarz, dan Daniel., ( 2013 ), Comparison Metal Water Jet Cutting With Laser and Plasma Cutting, Jurnal Prodecia Engineering, Vol. 69, 838-843.
Malik. I., Mardiana., Recxa, dan Abello A. A., ( 2021 ), Analisa Kekerasan Permukaan Hasil Pemotongan Pada Baja SS400 Menggunakan Mesin CNC Plasma Cutting Dengan Pengaruh Variasi Kuat Arus Dan Ketinggian Torch, Jurnal Austenit, Vol. 13 No. 2.
Manik, P., dan Chrismianto, D., ( 2015 ), Pelatihan Mould Loft (Lantai Gambar) Kapal Bagi Pengrajin/Pembuat Kapal Tradisional di Kabupaten Batang – Jawa Tengah, Jurnal KAPAL, Vol. 12, No. 3, 165-172.
Oliveira, A., and Gordo, J. M., ( 2018 ), Cutting processes in shipbuilding.
Peterson, D, R., ( 1983 ), "BRITSHIPS 2--A Computer Aided Design and Production System Using Computer Graphics." THE 1983 SPC/lREAPS TECHNICAL SYMPOSIUM. 1983.
Risqullah. H., Kardiman., dan Dirja, I., ( 2022 ), Proses Sandblasting Dalam Proses Fabrikasi Baja Struktur Pada Proyek Refinery Development Master Plan (RDMP) di PT AJP, Jurnal Ilmiah Wahana Pendidikan, Vol. 8, No. 15, 264-275.
Salonitis, K., and Vatousianos, S., ( 2012 ), Experimental Investigation of Plasma Arc Cutting Process, Jurnal Procedia CIRP 3, 287-292.
Saputra, B., Mulyanto, I, P., dan Amiruddin, W., ( 2017 ). Studi Perancangan Galangan Kapal untuk Pembangunan Kapal Baru dan Perbaikan di Area Pelabuhan Pekalongan, Jurnal Teknik Perkapalan, Vol. 5, No. 2.
Wibisana, A., Adlin, I. A., dan Indrawati, W., ( 2020 ), Ekonomi Teknik, Tangerang Selatan, UNPAM PRESS.
